Cold TS pipe ahead of 'hot' one until flush & switch

-
Caught a clear example of a very logical TS flow direction switch on the L1. The pipe that's designed to be the cooler one of the two is physically, when connecting to the brew group, lower and thus closer to the boiler. At warmup in the morning, it therefore heats up a tiny bit quicker than the upper pipe and for a few minutes it takes the lead with a flow from the lower pipe into the group and out of it through the upper pipe back into the heat exchanger.

During a short 200ml open port flush at minute 10, the upper pipe heats more from water flowing out of the HX pipe going through the boiler, the lower pipe cools a bit and then they both are at the ideal start position for the regular flow, heating up the brew group further.

Scace sitting next to the machine at 28ºC ambient temp.

Reacties

Een reactie posten

Populaire posts van deze blog

Finished Pavoni & Fuji PXG4 pid: Probe Inside the Ring

-
Afbeelding
Delicious cup: all the work was well invested! At the end of the previous blog about the pressostat and PID working together , I mentioned that I would like to clean up the xmas tree of wires and have as few cables and probes as possible to visually disturb the classic design of the La Pavoni. Getting rid of the probe that was fastened with copper tape to the top of the brew group was a priority. I wanted to hide a new probe in the cooling fin as close as possible to the brew group. This morning I asked Tije if he could do that. He would need to drill a straight hole of 3mm diameter in the 4mm inner ring of the cooling fin that sits as a tight clamp around the brew group. Always the optimist, Tije set to work: First, Tije made a piece of aluminum to fit the inside of the ring. Drilling a thin hole straight through the curved aluminum, if possible tangentially going through the inside of the ring to touch the brew head directly, you need the support of the temporary insid
Meer lezen

Tiny Cheap Fluid Bed Roaster by Tije and Jan

-
Afbeelding
(also see Daily Coffee News feature ) Tije designed and made the following structure for a tiny and cheap fluid bed roaster, to which Jan van der Weel added the Arduino parts, electronics and programming: Sketch by Tije de Jong Jan sourced a very cheap blower (€ 11) to start with, Tije developed and constructed the mechanics, Jan built together and programmed the TC4 / SSR electronics.  On his blog, Jan will specify exactly how the TC4 part is combined and programmed and I will copy these details into this blog entry, just as Jan will use this video in his blog. We did a few test roasts to make sure it works at all and it does. Towards the end, the first roast tended to get a flat BT line and airflow was slightly decreased. 200g seems max load of green beans. Second roast a little more power was given to the heater. Next we will try the Background Roast driven by the PID software of Artisan. A week later, with updated software that works better to change the fan
Meer lezen

KiwiSDR2 [radio]

-
Afbeelding
  Despite selling one and giving away two of the five monster vintage 'boat anchor' receivers that I had, I still enjoy listening to shartwave radio. The modern iCOM R8600 that I also have has a wider range plus some decoding options but it's not easy to figure out what encoding is used on which frequencies. The SDR-Control app from Marcus Roskosch at https://ham-radio-apps.com/ makes this much easier and also allows some remote control of the receiver so you can place it and an antenna at the top floor of your house while listening downstairs. I also got the SDRplay RSP1B box: This offers a great listening experience at a very low price compared to the iCOM hardware. I had one before and bought one again after a (somewhat limited) Mac version of the software became available. This device needs a computer to be connected to the receiver. For some time now a nifty little device has appeared which not only works standalone, it even allows you or anyone else to utilize the
Meer lezen